Accept : -- P.B. / M.S. / EMG. / Contact - Start / Stop / Limit switch / sensor

                   -- Interlock/selective Sw. - Proximity switch

                   -- Aux.contact of transducer / detector

 As I/O of S/W PLC Controller

 Quadrature encoder counter

 Industrial ON/OFF control

 Up / down or pulse / direction counter

 High speed counter

 PWM controller

 Trigger event counter

Features

 16 isolated DI and 16 isolated DO channels

 High voltage isolation on all isolated channel (2500Vac)

 Software debounce : No debounce, 100Hz, 200Hz, 1KHz 

 No output transition during start-up

 Output status readback

 External triggered interrupt (on IN07 ~ IN00)

 Keep output state after hot reset (jumper selectable)

 Quadrature counter function

 High speed timer counter function provides timer, counter and PWM function : Gate control; Counter input; Programmable trigger output

Specifications (With Matched Wiring Board)

Main Card -- Input Section

 Input :14 photo-isolated

 Interrupt : IN07 ~ IN00

                2 high speed magnetic coupler (TTL level)

 ON state : 2.8Vdc(max) 4.5mA(min)

                IN00 : Gate

 OFF state : 8Vdc(min) 3mA(max)

                IN01 : Ti

 Software debounce : No debounce, 100Hz, 200Hz, 1KHz

 Switching speed : 10KHz max. (limit by photo coupler speed and debounce filter)

Main Card -- Output Section

 Output : 14 photo-isolated

 Output rating : 3A @250Vac, 30Vdc(Relay)

                    2 high speed magnetic coupler (open collector)

                             1A @48Vdc(NMOS)

                    OUT00 : Tout

                             1A @24Vdc(PMOS)

                    OUT01 : General

                              2A @240Vac(SSR) 

 Output range : Open collector 0 ~ 45 Vdc (on card)

 Sink current : 500mA(peak) per channel(on card)

 Switching speed : 20KHz(max)(MOS out only)

Main Card -- Timer / Counter / PWM Section

 Timer time base : 1us

 Timer / counter length : 32-bit

 Counter frequency(max) : 8MHz

 PWM time base : 33MHz

 PWM frequency : 16-bit

 PWM duty : 16-bit

Main Card -- Quadrature counter

 Input multiple rate : X1, X2, X4 programmable (quadrature signal only)

 Maximum quadrature input frequency : 8MHz @X1, 5MHz @X2, 3MHz @X4

 Input mode: A,B phase (quadrature mode)

 Counter length : 32-bit

Main Card -- General

 Card ID : 4-bit

 Operation temperature : 0 to +70 degree C

 Insulation resistance : 100M Ohm(min) at 1000Vdc

 Storage temperature : -20 to +80 degree C

 Isolation voltage : 2500Vac 1Min

 Operation humidity : 5~95% RH, non-condensing

 Connector : Two 20-pin male flat cable connectors

 Dimensions : 130(W)*102(H) mm, 5.2(W)*4.1(H) in

DIN rail mounted wiring board

ADP3217DIN DIN rail mounted wiring board

 Power Requirement : 24Vdc ± 4Vdc

 Input : 6 with LED indicator, 2 specific timer / counter input

 Output : ADP3217DIN(R) : 6 Relay(3A @250Vac, 3A @30Vdc) with LED indicator, 2 high speed isolated open collector output

                   ADP3217DIN(S) : 6 SSR(2A @240Vac) with LED indicator, 2 high speed isolated open collector output

                   ADP3217DIN(P) : 6 PMOS(Source 1A @24Vdc) with LED Indicator, 2 high speed isolated open collector output

 Connector : One 20-pin male flat cable connector

 Operation Temperature : 0 to +70 degree C

 Operation Humidity : 5~95% RH, non-condensing

 Dimension : ADP3217DIN(R)/(P) : 86(W)*103(L)*45(H) mm, 3.4(W)*3.2(L)*2.1(H) in

                          ADP3217DIN(S) : 86(W)*103(L)*50(H) mm, 3.4(W)*4.1(L)*2.0(H) in

ADP9201DIN DIN rail mounted wiring board

 Power Requirement : 24Vdc ± 4Vdc

 Input : 8 with LED indicator

 Output : ADP9201DIN(R) : 8 Relay(3A @250Vac, 3A @30Vdc) with LED indicator

                   ADP9201DIN(N) : 8 NMOS(Sink 1A @48Vdc) with LED Indicator

                   ADP9201DIN(P) : 8 PMOS(Source 1A @24Vdc) with LED Indicator

                   ADP9201DIN(S) : 8 SSR(2A @240Vac) with LED indicator

 Connector : One 20-pin male flat cable connector

 Operation Temperature : 0 to +70 degree C

 Operation Humidity : 5~95% RH, non-condensing

 Dimension : ADP9201DIN(R)/(N)/(P) : 86(W)*103(L)*45(H) mm, 3.4(W)*3.2(L)*2.1(H) in

                        ADP9201DIN(S) : 86(W)*103(L)*50(H) mm, 3.4(W)*4.1(L)*2.0(H) in

JS51053 20PM DIN rail mounted wiring board

 Connection cable : 20-pin flat cable to connect main and wiring board

 Dimension : 86(W)*79(L)*52(H) mm, 3.4(W)*3.2(L)*2.1(H) in

 Driver, DLL, Demo and Example Program

Manual

 Catalog

WinXP/7(32bit)

Win7(64bit)

Win10(32bit)

Win10(64bit)

 Labview 

 Linux 2.6

 Hardware

 Software

 Main Card

 Wiring Board

 Driver

 Driver

  Driver

 Driver

PRODUCT

DESCRIPTIONS

 1.

DIO3217

32-channel Digital I/O Card for 16 DI and 16 D0 Photo-coupler isolated with Multifunction timer / counter

 2.

ADP3217DIN(S)

DIN rail mounted wiring board matched DIO3217 with 12 I/O LED indicators, SSR output for 6 DI, 6 DO and 2 high speed TTL input, 2 high speed open collector output

 3.

ADP3217DIN(R)

DIN rail mounted wiring board matched DIO3217 with 12 I/O LED indicators, Relay output for 6 DI, 6 DO and 2 high speed TTL input, 2 high speed open collector output

 4.

ADP3217DIN(P)

DIN rail mounted wiring board matched DIO3217 with 12 I/O LED indicators, PMOS output for 6 DI, 6 DO and 2 high speed TTL input, 2 high speed t open collector output

 5.

ADP9201DIN(R)

DIN rail mounted wiring board with 16 I/O LED indicators and Relay output for 8 DI, 8 DO

 6.

ADP9201DIN(N)

DIN rail mounted wiring board with 16 I/O LED indicators and NMOS output for 8 DI, 8 DO

 7.

ADP9201DIN(P)

DIN rail mounted wiring board with 16 I/O LED indicators and PMOS output for 8 DI, 8 DO

 8.

ADP9201DIN(S)

DIN rail mounted wiring board with 16 I/O LED indicators and SSR output for 8 DI, 8 DO

 9.

JS51053

DIN rail mounted dummy wiring board

 10.

M23207

20-pin flat cable 1.5 M for ADP9201_JM1/ADP9201_JM2

 11.

M23209

20-pin flat cable 3.0 M for ADP9201_JM1/ADP9201_JM2